Surfergal

8 weeks to xmas
http://craft.dow.com/craft/proj/1906.htm



Materials:
STYROFOAM* Brand Foam Ball, 1-1/2"
Assorted ribbons, 1/4"-3/8" wide (model shown uses grosgrain, curling, sheer, and satin)
Ruler
Wooden skewers, two
Heavy glass or jar
Scissors
Low-temp glue gun and glue sticks
Thick, white craft glue

Instructions
1. Cut several 3-1/2"-4" lengths from a variety of ribbons. If using curling ribbon, cut 7"-8" lengths. Curl ribbons before attaching to foam ball.
2. Insert one skewer into bottom of ball. Holding skewer, place dot of white glue on ball surface. Center one ribbon length over glue dot and use second skewer to push ribbon 1/4" into foam ball, twisting slightly to secure. Remove skewer.

3. Continue adding ribbons in same way until entire ball is covered. Place skewer in heavy glass or jar to let ball dry.
4. Remove skewer. Cut 6" ribbon length. Knot ribbon ends to make hanging loop. Apply glue to knot and use skewer to push hanger into top of ball. Let dry

http://craft.dow.com/proj/47.htm


Materials:
STYROFOAM* Brand Foam 3" ball
Shimmering red satin fabric, 11" circle
Assorted small beads: round and flat glass; pearls
22-gauge brass wire
Metallic gold sheer wire-edge ribbon, 1/3 yd.
Scissors
Ruler
Sewing needle and matching red thread
Needlenose pliers
Wire cutters
Wooden skewer
Compass (optional)

INSTRUCTIONS:
1. Sew a gathering stitch 1-1/4" from edge of fabric circle. Center foam ball on wrong side of fabric circle. Pull threads to gather fabric at top of ball and knot to secure. Arrange pleats evenly around ball. Wrap an 18" length of wire tightly around gathered fabric, using pliers for added grip. Twist wires ends together, tucking ends back under wrapped wires to secure. Neatly trim gathered fabric above wire.
2. When cutting wires, cut ends to a point. Cut 10 - 12 1" lengths of wire. Wrap center of each 1" length around a wooden skewer, resulting in a U-shape wire. These u-shaped pins will help secure wire embellishments.
3. Cut a length of wire 24" or longer. At top of ball, carefully insert one end of wire through satin and into foam ball 1-1/2". Using photo as a guide, wrap wire around ball, stringing on beads as desired. Cut wire, leaving a 1" tail; using pliers, bend tail at a 90° angle and insert into foam ball. Insert a U-shape pin over end of wrapped wire to secure.
4. Continue embellishing ornament as desired, using following techniques (refer to photo):
Wrap ball with an additional length of beaded wire.
String beads on U-pins and insert in the foam, crossing over wires.
Shape a short length of wire into a loose spiral with your fingers, stringing on beads as desired. Cut wire; bend each end at 90° angle. Press ends into foam to attach spiral to ball. Press U-shape wires over spiral as needed to secure.
Wrap a short length of wire around a wooden skewer to form a coil. Cut wire, leaving a 1" tail at each end. Bend ends at a 90° angle and attach coil to ball. For variety, form a suspended coil by bending a tiny loop at one end of wire and then wrapping wire around skewer as before. Pin loop end of coil to ornament with a U-shape wire, letting opposite end hang free. Note: If stringing beads on a suspended coil, be sure to add a tiny loop in free end to secure them.
Twist two identical lengths of wire together, gripping one end with pliers and winding opposite end with your fingers. Trim 3/4" from one wire only at each end of twisted length. Snip sharp points in longer untrimmed wires and then bend at a 90° angle. Shape twisted wire as desired and attach to ornament by pressing ends into foam.

5. Cut an 8" length of wire for hanger. Insert ends of hanger under wire wrapped around top of ornament and then bend ends up 1/2" to secure. Tie ribbon in a bow around top of ornament

http://craft.dow.com/craft/proj/957.htm


Materials:
STYROFOAM* Brand Foam Ball, 4"
Ribbons, 1-1/2" wide: gold metallic, 4 yds.; sheer burgundy, 2 yds.; desired color, 2 yds.
Violet/blue fiber assortment
Craft wire: 22-gauge magenta; 24-gauge gold
Assorted beads, jewels and gems
Pencil
Ruler
Scissors
Pins: straight; pearl-head corsage, 2"
Wire cutters
Low-temp glue gun and glue sticks
Thick, white craft glue


Instructions
1. Wrap foam ball with gold ribbon, covering surface. Dip several straight pins in glue and insert into ball to secure ribbon.
2. Wrap gold wire randomly around ball. Wrap wire around random straight pins to secure. Glue and insert wire ends into ball to secure.
3. In same way, twist and wrap remaining ribbons around ball, allowing gold ribbon and wire to show through.
4. Cut 36" length from magenta wire. Wrap wire around pencil to curl. Thread wire with beads and gems as desired, twisting wire around beads to secure. Glue and insert one wire end into ball, then randomly wrap wire around ball, securing with pearl-head pins inserted through some beads. Glue free wire end into ball.
5. Wrap ball with fibers; secure with pins and glue. Continue wrapping ball with wire and fibers until highly-textured surface is achieved.
6. To make ornament, cut 12" length from wire. Twist wire ends to secure and glue into top of ball for hanger.